Pulnix TS-9720EN Series Instrukcja Instalacji Strona 80
- Strona / 116
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Page 68
VIS CAM 300/400 Installation Manual
Appendix B: J-Panel Functional and Connector Description
6.2 X1: J-panel connection to Camera 0
FIGURE 64. Connecting from J-Panel to camera zero.
6.2.1 Functionality
Power and data connection to the EN camera. The 24V power supply for all camera functions (Camera,
I/O Board, light and heaters), Ethernet and RS485 data communication is connected by means of this
connector.
6.2.2 Connector specification
Connector type: 16 pole WAGO pluggable terminal block
Connector on board: WAGO 734-246
Cable part: WAGO 734-216
6.2.3 Connector signal specifications
6.2.3 (a) Lane Controller interface
Description
RS485 two wire half-duplex multi-drop communication network. The I/O Board has connections for
daisy chain configuration. The two signal pairs (RS485D+ and RS485D-) can be reversed.
Signal levels:
Standard RS485 communication levels.
Electrical interface on the J-Panel:
The signals are connected to J-Panel X15 pin 1 and 2. There are termination resistors on the board. See
Figure 49 on page 53 for a description of the signal path.
- Vehicle Imaging 1
- Subsystem 300/400 1
- Warranty 3
- Certifications 3
- WARNING 4
- Table of Contents 5
- Page vii 7
- Page viii 8
- List of Figures 9
- List of Tables 11
- Page xii 12
- 1 Introduction 13
- FIGURE 1. VIS elements 14
- 1.3.2 VISCAM 15
- 1.3.3 Illumination 16
- 1.3.4 VJP-300 Junction Panel 16
- 1.3.5 RS485 Device Server 16
- 1.4 Operational Overview 17
- 2 Preparing for installation 18
- Preparing for installation 21
- 1. Disconnect Power 27
- 3.2 Installing the Camera(s) 29
- 3.3 Installing the J-Panel 33
- FIGURE 24. Test trigger 38
- 3.4 Illumination Options 40
- 1 2 3 4 5 6 40
- 1 2 3 4 5 6 7 8 42
- 4 System Set-Up 43
- 5.1 I/O Board Layout 56
- 5.2.1 Functionality 57
- FIGURE 40. Interface drawing 58
- 5.2.6 Typical wiring diagram 61
- 5.3.1 Functionality 62
- FIGURE 46. Switch location 63
- TABLE 12. Wiring diagram 63
- 5.3.5 Typical Wiring Diagram 64
- 5.3.7 Functionality 65
- FIGURE 53. Connecting to a 2 68
- FIGURE 56. Detection board 70
- 5.5.1 Functionality 71
- TABLE 14. Connector table 72
- 5.6.1 Functionality 73
- 5.6.5 Test setup 1 75
- 5.6.6 Test setup 2 76
- 5.7.1 Functionality 77
- 5.8 Cables 78
- 6.1 J-Panel Layout 79
- Description 81
- 6.2.5 Typical Wiring diagram 82
- 6.2.6 Indicators 83
- 6.2.7 Switches 83
- 6.3.1 Functionality 84
- 6.3.2 Connector specification 84
- TABLE 20. Signal table 85
- 6.3.5 Typical Wiring diagram 86
- 6.3.6 Indicators 87
- 6.3.7 Switches 87
- 6.4.1 Functionality 88
- 6.4.5 Indicators 89
- 6.7 X6, X7: 24V DC Power 92
- FIGURE 76. RS485 to Ethernet 94
- 6.11 X14: External Trigger 97
- FIGURE 81. Trigger 0 98
- FIGURE 82. Trigger 1 98
- TABLE 32. Connector table 98
- 6.12.1 Functionality 99
- Master to slave connections 103
- FIGURE 86. Terminal block 104
- Page 100 112
- Page 101 113
- Page 102 114
- www.jai.com 116
Powiązane produkty i podręczniki dla Aparaty z pseudo lustrem Pulnix TS-9720EN Series
(72 strony)Bauknecht GSFS PRESTIGE Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Bauknecht GSFS PRESTIGE.
Wir stellen 1 PDF-Handbücher Bauknecht GSFS PRESTIGE zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Installationshandbuch
Komentarze do niniejszej Instrukcji